Foldeporte
Foldeporte fra Lockhart.
Stabilitet, styrke, pålidelige og funktionelle.
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Morbi nec lectus tellus. In dignissim lacus tempor massa aliquet pulvinar. Vestibulum mi ipsum, maximus ut felis et, consectetur facilisis nisi. Donec quis nulla venenatis, commodo purus et, fringilla ante. Nulla nec maximus urna.
Sed eu ligula pretium, pellentesque nibh et, ullamcorper sapien. Suspendisse efficitur bibendum quam, eu cursus magna hendrerit eget. Suspendisse fermentum dui et sapien varius tincidunt. Nam mollis turpis et nulla gravida varius. Duis facilisis sagittis nunc eget vestibulum. Mauris non elementum justo, et tincidunt mi. Morbi iaculis leo felis, vestibulum dignissim ipsum eleifend sit amet. Vestibulum vitae ex porttitor, malesuada tortor in, porttitor nulla.
LIGHT AL601F
LIGHTWEIGHT AND ELEGANT, BUT STILL STURDY AND DURABLE.
This best describes the aluminium folding door AL601F – our lightest folding door.
Information
GENERAL INFORMATION
Aluminium folding door with frame-lattice design. Design depth of 60 mm. Wall thickness of at least 2 mm.
Frame profiles are connected to the leaf of a folding door by means of double bolts.
40 mm finger-pinch protective rubber between the door leaves. Panels made of aluminium or insulating glass.
The door leaves are suspended by guided roller units.
The track rollers and door leaves are supported by dust-proof, maintenance-free ball bearings.
Adjustable hinges and guide bolts that are 16 mm thick. Covered bolt lock.
Creating an opening for people to pass through occurs with no loss in stability.
All of the door components can be replaced easily without damaging other components!
SIZES
– maximum width of door leaves: 1200 mm (door width: 4 + 0 = 4800 mm)
– maximum height of door leaves: 4500 mm
GLAZING
Insulating tempered glass of up to 1 m2 per door leaf. Plastic glazing with no limitations. Glazing as dry glazing with rubber sealing on both sides.
PANELS
1 mm thick aluminium sheets glued to 30 mm of rigid-foam styrofoam. Attached by means of clamped aluminium holding strips. Panels can be replaced easily.
SURFACE FINISH
– powder-coated with façade quality, standard colour of your choice
– anodised with A6/C0
OPERATION
– manually operated
– power-operated with folding door drive BASIC
Tekniske specifikationer
SLIDING BOLT MECHANISM
Manually operated doors are equipped with an inner sliding bolt mechanism and covered, built-in lock bars made of galvanised square steel bar.
Operation via a robust steel loop lever and a cased lock that is integrated into the profile.
GLAZING BEADS
The double-walled insulated shatterproof glass is installed from inside with clamped aluminium glazing beads and rubber seals. This ensures that the glass can be replaced easily, for instance when repairs are necessary. Glazing is generally in the form of dry glazing with rubber sealing on both sides
HINGES
The individual door leaves are connected to each other by means of solid, adjustable metal hinges. Diameter of hinge pins is 16 mm; with dust-proof thrust bearing.
GUIDE RAIL WITH ROLLER UNITS
The guide rail is only open at the bottom, and has an integrated seal carrier and continuous lip sealing. The door leaves are suspended by roller units. The track rollers are supported by dust-proof, maintenance-free ball bearings. The dimensions are adapted to suit the load that each type of door can handle
ROBUST AL602F
THE DOOR DESIGNED TO MEET ANY REQUIREMENTS.
Folding doors are, in principle, very simple, yet they are very diverse in terms of their range of application. From small workshop doors to fire-brigade doors and gigantic aeroplane hangar doors, folding doors always meet their requirements
Information
GENERAL INFORMATION
Aluminium folding door with frame-lattice design. Design depth of 60 mm. Wall thickness of at least 2 mm. Frame profiles are connected to the leaf of a folding door by means of double bolts. Pressed-in aluminium component as a static connecting element. 50 mm finger-pinch protective rubber between the door leaves. Panels made of aluminium or insulating glass. The door leaves are suspended by horizontally-guided roller units and plastic-covered track rollers. The track rollers and door leaves are supported by dust-proof, maintenance-free ball bearings. Adjustable hinges and guide bolts that are 20 mm thick. Covered bolt lock. Creating an opening for people to pass through occurs with no loss in stability. All of the door components can be replaced easily without damaging other components!
SIZES
– maximum width of door leaves: 1300 mm (door width: 6 + 6 = 15600 mm)
– maximum height of door leaves: 5600 mm
GLAZING
Insulating tempered glass of up to 2 m2 – continuous – per door leaf. Complete glazing of doors is possible. Glazing as dry glazing with rubber sealing on both sides.
PANELS
1 mm thick aluminium sheets glued to 30 mm of rigid-foam styrofoam.
Attached by means of clamped aluminium holding strips. Panels can be
replaced easily.
SURFACE FINISH
– powder-coated with façade quality, standard colour of your choice
– anodised with A6/C0
OPERATION
– manually operated
– power-operated with folding door drive BASIC or POWER
SLIDING BOLT MECHANISM
Manually operated doors are equipped with an inner sliding bolt mechanism and covered, built-in lock bars made of galvanised square steel bar. Operation via a robust aluminium loop lever and a cased lock that is integrated into the profile.
GLAZING BEADS
The double-walled insulated shatterproof glass is installed from inside with clamped aluminium glazing beads and rubber seals. This ensures that the glass can be replaced easily, for instance when repairs are necessary. Glazing is generally in the form of dry glazing with rubber sealing on both sides.
HINGES
The individual door leaves are connected to each other by means of solid, adjustable metal hinges. Diameter of hinge pins is 20 mm; with dust-proof thrust bearing.
GUIDE RAIL WITH ROLLER UNITS
The guide rail is only open at the bottom, and has an integrated seal carrier and continuous lip sealing. The door leaves are suspended by roller units. The track rollers are supported by dust-proof, maintenance-free ball bearings. The dimensions are adapted to suit the load that each type of door can handle.
THERMO AL603F
THERMALLY SEPARATED – A DOOR LIKE NO OTHER
Thermally separated profiles mean greater heat insulation and provide a solution for modern requirements. Two separated extruded aluminium profiles are connected by means of a glass-fibre reinforced plastic strip. This significantly reduces the heat flow from inside to outside, yet the overall stability of the design is not diminished.
Information
GENERAL INFORMATION
Aluminium folding door with thermally-separated frame-lattice design. Design depth of 60 mm. Wall thickness of at least 2 mm.
Frame profiles are bolted together and glued to the leaves of the folding door using mitres. 50 mm finger-pinch protective rubber between the door leaves. Panels made of aluminium or insulating glass. The door leaves are suspended by horizontally-guided roller units and plastic-covered track rollers. The track rollers and door leaves are supported by dust-proof, maintenance-free ball bearings.
Adjustable hinges and guide bolts that are 20 mm thick. Covered bolt lock. Creating an opening for people to pass through occurs with no loss in stability.
SIZES
– maximum width of door leaves: 1300 mm (door width: 6 + 6 = 15600 mm)
– maximum height of door leaves: 5600 mm
GLAZING
Insulating tempered glass of up to 2 m2 – continuous – per door leaf. Complete glazing of doors is possible. Glazing as dry glazing with rubber sealing on both sides.
PANELS
1 mm thick aluminium sheets glued to 30 mm of rigid-foam styrofoam. Attached by means of clamped aluminium holding strips. Panels can be replaced easily.
SURFACE FINISH
– powder-coated with façade quality, standard colour of your choice
– anodised with A6/C0
OPERATION
– manually operated
– power-operated with folding door drive BASIC or POWER
SLIDING BOLT MECHANISM
Manually operated doors are equipped with an inner sliding bolt mechanism and covered, built-in lock bars made of galvanised square steel bar.
Operation via a robust aluminium loop lever and a cased lock that is integrated into the profile.
GLAZING BEADS
The double-walled insulated shatterproof glass is installed from inside with clamped aluminium glazing beads and rubber seals. This ensures that the glass can be replaced easily, for instance when repairs are necessary. Glazing is generally in the form of dry glazing with rubber sealing on both sides.
HINGES
The individual door leaves are connected to each other by means of solid, adjustable metal hinges. Diameter of hinge pins is 20 mm; with dust-proof thrust bearing.
GUIDE RAIL WITH ROLLER UNITS
The guide rail is only open at the bottom, and has an integrated seal carrier and continuous lip sealing. The door leaves are suspended by roller units. The track rollers are supported by dust-proof, maintenance-free ball bearings. The dimensions are adapted to suit the load that each type of door can handle.
STRONG ST602F
STRONG AND RELIABLE FOR CONTINUOUS USE
In this area, the steel folding door ST602F cannot be surpassed. Particularly suitable for very large and fully-glazed doors.
Information
GENERAL INFORMATION
Steel folding door with frame-lattice design. Design depth of 60 mm. Wall thickness of at least 2 mm. Frame profiles are connected to the leaves of the folding door using mitres and by means of brazing. 50 mm finger-pinch protective rubber between the door leaves. Panels made of steel or insulating glass. The door leaves are suspended by horizontally-guided roller units and plastic-covered track rollers. The track rollers and door leaves are supported by dust-proof, maintenance-free ball bearings.
Adjustable hinges and guide bolts that are 20 mm thick. Covered bolt lock. Creating an opening for people to pass through occurs with no loss in stability.
SIZES
– maximum width of door leaves: 1300 mm (door width: 6 + 6 = 15600 mm)
– maximum height of door leaves: 7000 mm
GLAZING
Insulating tempered glass of up to 4 m2 – continuous – per door leaf. Complete glazing of doors is possible. Glazing as dry glazing with rubber sealing on both sides.
PANELS
1 mm thick steel sheets glued to 30 mm of rigid-foam styrofoam. Attached by means of clamped aluminium holding strips. Panels can be replaced easily.
SURFACE FINISH
– powder-coated with façade quality, standard colour of your choice
OPERATION
– manually operated
– power-operated with folding door drive BASIC or POWER
SLIDING BOLT MECHANISM
Manually operated doors are equipped with an inner sliding bolt mechanism and covered, built-in lock bars made of galvanised square steel bar.
Operation via a robust aluminium loop lever and a cased lock that is integrated into the profile.
GLAZING BEADS
The double-walled insulated shatterproof glass is installed from inside with clamped aluminium glazing beads and rubber seals. This ensures that the glass can be replaced easily, for instance when repairs are necessary. Glazing is generally in the form of dry glazing with rubber sealing on both sides.
HINGES
The individual door leaves are connected to each other by means of solid, adjustable metal hinges. Diameter of hinge pins is 20 mm; with dust-proof thrust bearing.
GUIDE RAIL WITH ROLLER UNITS
The guide rail is only open at the bottom, and has an integrated seal carrier and continuous lip sealing. The door leaves are suspended by roller units. The track rollers are supported by dust-proof, maintenance-free ball bearings. The dimensions are adapted to suit the load that each type of door can handle.
HAR DU BRUG FOR HJÆLP?
Kan du ikke finde det du søger på vores hjemmeside eller har du noget specielt, du gerne vil tale med en professionel fagmand om – så kontakt os endelig. Vi er behjælpelig med at rådgive og vejlede.